Category Archives: ZAR Formenti RIBS

ZAR75

Posted on by

ZAR75

Features

  • 3 rows that can seat 10 persons forward running;
  • anchor forepeaks and afterpeaks;
  • back peak with the mooring accessories;
  • front sun bathing bed convertible into a double bed (cm 160 x 230) with extensions as an optional;
  • wide stem dinette with a table as an optional;
  • wide back dinette with a table included (Suite);
  • 175 x 180 back sunbathing bed (with the two back rests in the horizontal position);
  • two-seater console (that can be located in the middle or on the side of the boat) with a hydraulic wheelhouse, stainless steel rudder, 2 internal watertight compartments with door, an object holder and two peaks under the front seat, wc -as an optional;
  • three-seater multifunctional anatomic driver’s couch with double driving position (sitting up and down);
  • kitchen area under the driver’s couch equipped with:sink, mincing board (also utilizable like a place for a mono/double gas ring) and refrigerator special compartment predisposition;
  • bilge pump;
  • 8 stainless steel handles for passengers safety;
  • foldaway stainless steel ascent ramp and double VTR bridge;
  • 2 stainless steel fuel tanks (about 200+200 litres for Zar 75 and Zar 75 Suite) located under the walk floor according to standards;
  • 1 stainless steel fuel tank (about 200 for Zar 75 Plus and Zar 75 Suite Plus) located under the walk floor according to standards;
  • 6 handling handles;
  • 4 stainless steel bollards;
  • perimetric double millpond;
  • polished stainless steel 9 Kg anchor;
  • anchor-winch nose with stainless steel bow;
  • 3 stainless steel eyebolts for hangers.

Optional Equipment

  • Stainless steel roll-bar with fibreglass bases
  • Roll-bar installation with running lights,anchorage lights, horn and wiring
  • Beacon ready installed on roll-bar/console
  • Prow sunbed extension each (not for Plus version)
  • Prow complete table
  • Auxiliary engine support
  • Total sheet for night and travelling
  • Console cover
  • Seat cover
  • Electric panel
  • Shower Complete (for stern and external wash basin) with surge tank, tank in prow, outdoor embarkation and installation
  • Complete dingy heuling belt kit for launch/accommodation
  • Anchor windlass installed with motor, cable, chain and double controls (in console and anchor housing)
  • Wake board kit complete with counterplates
  • Left stern deck with folding ladder (single and double engine)
  • Right stern deck (single and double engine)
  • Modification kit from Zar 75 to Zar 75 suite
  • Modification kit installation from Zar 75 to Zar 75 suite
  • Console change kit from ZAR 75 to ZAR 75 plus
  • Installation console change
  • Eletric refrigerator (12/24V)
  • Flexi-teak for cockpit
  • Flexi teak for the bridges + covers (4pz)
  • Flexi teak for the bridges (2pz)
  • Flexi-teak installation
  • Nautical camping tent
  • Sunroof 3 arch
  • Rear telescopic sun-cover for roll-bar
  • Prow sunroof (rear telescopic sun-coverextension)
  • Pair of canopies (dx-sx) for telescopic sun-cover
  • Pair of canopies (dx-sx) for prow sun-bathing bed extension

Technical Data

  • Static self emptying
  • Homologation “CE cat. “B”
  • Length m 7.42
  • Width m 2.82
  • Internal walking length m 7.35
  • Internal walking width m 2.20
  • Intertubular width m 1.68
  • Tubular diameter cm 58
  • tubular compartments n. 6
  • Seating capacity n. 14
  • Net dinghy weight kg 1,100
  • (with standard equipment, withoutliquids and motor) ± 10% variable datum
  • Maximum power applicable kW 225 / HP 300
  • Minimum power applicable(minimum performance) HP 130
  • Power recommended (average performance) HP 150/250
  • Engine shaft length XL
  • weight installable motors kg 480
  • CE certification with “B” design category and CE type testing. (A+a form).

Further Accessories Only For Plus Version

  • Electric sea WC with installed direct discharge
  • Electric sea WC with installed black water tank
  • Console cover
  • Shower (for stern external wash basin and bathroom in console) complete with autoclave, tank in prow, outdoor embarkation, discharge pump and installation
  • Prow sunbed extension each (for Plus version)
  • Installation supplementary water tank of about 67 litres
  • Supplementary 80 lt fuel tank in the bow
  • Supplementary 80 lt fuel tank installation
  • 8 plug electrical panel

ZAR73 Skydeck Outboard

Posted on by
slide 1
Img
Img
ZAR73 Skydeck Outboard 3
ZAR73 Skydeck Outboard 4
ZAR73 Skydeck Outboard 5
ZAR73 Skydeck Outboard 6
ZAR73 Skydeck Outboard 7
ZAR73 Skydeck Outboard 9
previous arrow
next arrow

ZAR73 Skydeck Outboard

ZAR73 Concept

  • stern sun deck with folding ladder ;
  • full set of stern cockpit cushions;
  • 1 wash basin in external cockpit;
  • stern sunbathing area;
  • bow sunbathing area;
  • cabin cushions with wall padding;
  • 6 cabin cushions;
  • 2 cabin cushions with SKY DECK stitching;
  • mechanical + hydraulic steering gear;
  • hydraulic steering gear (only included in outboard version);
  • 2 batteries with isolator switch (not included in outboard version);
  • framed windscreen;
  • Plexiglass cabin entrance door;
  • framed opening side windows;
  • cabin with sliding door for bath/shower;
  • wash basin for cabin bathroom;
  • sea/chemical WC fi tting;
  • 2 mirrors (cabin + bathroom);
  • anchor winch nose + stainless steel bow;
  • about 270 lt fuel tank;
  • about 67 lt water tank;
  • autoclave pump system for internal and external showers;
  • electric panel;
  • 9 instruments on console;
  • dinette wooden table;
  • cold spotlights for cabin and bathroom;
  • blue Plexicor bathroom top;
  • repairs kit;
  • a pair of paddles;
  • bilge pump;
  • infl ating device;
  • stainless steel rudder;
  • 4 stainless steel bollards;
  • 3 stainless steel eyebolts for hangers;
  • 10 stainless steel handles for passengers safety.

ZAR73 Limited

  • stern sun deck with folding ladder ;
  • full set of stern cockpit cushions;
  • 1 wash basin in external cockpit;
  • stern sunbathing area;
  • bow sunbathing area;
  • cabin cushions with wall padding;
  • 6 cabin cushions;
  • 2 cabin cushions with SKY DECK stitching;
  • mechanical + hydraulic steering gear;
  • hydraulic steering gear (only included in outboard version);
  • 2 batteries with isolator switch (not included in outboard version);
  • framed windscreen;
  • Plexiglass cabin entrance door;
  • framed opening side windows;
  • cabin with sliding door for bath/shower;
  • wash basin for cabin bathroom;
  • electric sea WC with macerator;
  • black water tank with second eletric macerator;
  • 2 mirrors (cabin + bathroom);
  • 7 kg. stainless steel anchor;
  • anchor winch nose + stainless steel bow;
  • about 270 lt fuel tank;
  • about 67 lt water tank;
  • autoclave pump system for internal and external showers;
  • wastewater collection and discharge tank;
  • electric panel;
  • n. 9 instruments on console;
  • dinette wooden table;
  • cold spotlights for cabin and bathroom;
  • upright 50 l compressor fridge;
  • two burner cooker (excluding connection and gas cylinder);
  • stainless roll-bar with navigation lights, anchor lights, horn and headlight;
  • cockpit total sun tend;
  • blue Plexicor bathroom top;
  • shore battery charger (not included in outboard version);
  • anchor windlass controlled from console and remote control handset;
  • Flexi-teak cabin and bathroom interior;
  • repairs kit;
  • a pair of paddles;
  • bilge pump;
  • infl ating device;
  • stainless steel rudder;
  • 4 stainless steel bollards;
  • 3 stainless steel eyebolts for hangers;
  • 10 stainless steel handles for passengers safety.

Technical Data

  • Static self emptying
  • Homologation “CE cat. “B”
  • Length m 7,30
  • Width m 2,54
  • Internal walking length m 7,10
  • Internal walking width m 2,00
  • Intertubular width m 1,50
  • Tubular diameter cm 53
  • Tubular compartments n° n. 6
  • Seating capacity n. 10
  • Net dinghy weight (with standard equipment
  • and engine and without fluids in tanks);10% variable datum
  • Concept kg 1.400
  • Limited kg 1.700
  • Power outboard version maximum applicable CV 250
  • Power outboard version minimum applicable CV 200

Optional Equipment

  • autoclave shower system with a water tank of about 60 l. under the walk floor;
  • stainless steel tilting roll bar with go ahead lights, anchorage lights, horn;
  • beacon;
  • auxiliary motor support;
  • electric panel;
  • stainless steel plate and anchor-winch nose for electric anchor windlass predisposition;
  • anchor windlass installation with motor, cable, chain and control.

ZAR65 Suite Plus

Posted on by
slide 1
Img
Img
previous arrow
next arrow

ZAR65 Suite Plus

Features

  • 3 rows that can seat 8 persons forward running;
  • anchor forepeaks and afterpeaks;
  • back peak with the mooring accessories;
  • front sun bathing bed convertible into a double bed (cm 150 x 195) with extension as an optional;
  • wide stem dinette with a table as an optional;
  • wide back peak;
  • wide front peak;
  • wide back dinette with a table included (only Suite version);
  • two side peaks in the stem sides;
  • 160 x 190 back sunbathing bed (with the back rest in the horizontal position);
  • two-seater console with a hydraulic wheelhouse, stainless steel rudder, 1 internal compartment with door, an object holder and four peaks under the driver’s couch and under the front seat. Reclining driver’s couch;
  • bilge pump;
  • repairs kit;
  • inflating device;
  • a pair of paddles;
  • 8 stainless steel handles for passengers safety;
  • foldaway stainless steel ascent ramp and double VTR bridge;
  • 1 reticular polypropylene fuel tank (about 240 litres) according to standards CE;
  • 6 handling handles;
  • 4 stainless steel bollards;
  • perimetric double millpond;
  • polished stainless steel 9 Kg anchor;
  • anchor-winch nose with stainless steel bow;
  • 3 stainless steel eyebolts for hangers.
  • Dinette with a U-divan and special console with sea/chemical WC and shower fitting

Technical Data

  • Static self emptying
  • Homologation "CE cat. "B"
  • Length m 6,50
  • Width m 2,55
  • Internal walking length m 6,40
  • Internal walking width m 2,00
  • Intertubular width m 1,50
  • Tubular diameter cm 53
  • Watertight compartments n. 6
  • Seating capacity n. 12
  • Net dinghy weight (without equipment, liquids or motor) ± 10% variable datum kg 880
  • Maximum power applicable kW 166/HP 225
  • Minimum power applicable (minimum performance) HP 85/CV115
  • Power recommended (average performance) HP 140/180
  • Engine shaft lenght L
  • on demand XL
  • Max. weight installable motors kg 400
  • CE certification with “B” design category and CE type testing. (A+a form).

Optional Equipment

  • Stainless steel roll-bar
  • Roll-bar installation with running lights, anchorage lights, horn and wiring
  • Beacon ready installed on roll-bar/console
  • Sunbed extension
  • Prow complete table
  • Auxiliary engine support
  • Total night cover
  • Partial night cover
  • Console cover
  • Seat cover
  • Eletric panel
  • Left stern deck with folding ladder
  • Right stern deck
  • Shower Complete with surge tank, tank in prow, outdoor embarkation and installation
  • Complete dingy heuling belt kit for launch/accommodation
  • Anchor windlass installed with motor, cable, chain and double controls (in console and anchor housing)
  • Wake board kit complete
  • with counterplates
  • Modification kit from Zar 65 to Zar 65 suite
  • Modification kit installation from Zar 65 to Zar 65 suite
  • Dashboard with ladder for double engine installation
  • Eletric refrigerator (12/24V)
  • Modification of the ZAR 65 driver’s seat (for boats manufactured before September 2005)
  • Flexi-teak for cockpit
  • Felxi teak for the bridges + covers (4pz)
  • Felxi teak for the bridges (2pz)
  • Flexi-teak installation
  • Nautical camping tent
  • Sunroof 3 arch
  • Rear telescopic sun-cover for roll-bar
  • Prow sunroof (rear telescopic sun-cover extension)
  • Side canopy(1) for telescopic sun-cover

ZAR65 Suite

Posted on by
slide 1
slide 1
Img
Img
Img
previous arrow
next arrow

ZAR65 Suite

Features

  • 3 rows that can seat 8 persons forward running
  • anchor forepeaks and afterpeaks
  • back peak with the mooring accessories
  • front sun bathing bed convertible into a double bed (cm 150 x 195) with extension as an optional
  • wide stem dinette with a table as an optional
  • wide back peak
  • wide front peak
  • wide back dinette with a table included (only Suite version)
  • two side peaks in the stem sides
  • 160 x 190 back sunbathing bed (with the back rest in the horizontal position)
  • two-seater console with a hydraulic wheelhouse, stainless steel rudder, 1 internal compartment with door, an object holder and four peaks under the driver’s couch and under the front seat. Reclining driver’s couch
  • bilge pump
  • repairs kit
  • inflating device
  • a pair of paddles
  • 8 stainless steel handles for passengers safety
  • foldaway stainless steel ascent ramp and double VTR bridge
  • 1 reticular polypropylene fuel tank (about 240 litres) according to standards CE
  • 6 handling handles
  • 4 stainless steel bollards
  • perimetric double millpond
  • polished stainless steel 9 Kg anchor
  • anchor-winch nose with stainless steel bow
  • 3 stainless steel eyebolts for hangers.dinette with a U-divan

Technical Data

  • Static self emptying
  • Homologation "CE cat. "B"
  • Length m 6,50
  • Width m 2,55
  • Internal walking length m 6,40
  • Internal walking width m 2,00
  • Intertubular width m 1,50
  • Tubular diameter cm 53
  • Watertight compartments n. 6
  • Seating capacity n. 12
  • Net dinghy weight (without equipment, liquids or motor) ± 10% variable datum kg 880
  • Maximum power applicable kW 166/HP 225
  • Minimum power applicable (minimum performance) HP 85/CV115
  • Power recommended (average performance) HP 140/180
  • Engine shaft length L
  • on demand XL
  • Max. weight installable motors kg 400
  • CE certification with “B” design category and CE type testing. (A+a form).

Optional Equipment

  • Stainless steel roll-bar
  • Roll-bar installation with running lights, anchorage lights, horn and wiring
  • Beacon ready installed on roll-bar/console
  • Sunbed extension
  • Prow complete table
  • Auxiliary engine support
  • Total night cover
  • Partial night cover
  • Console cover
  • Seat cover
  • Electric panel
  • Left stern deck with folding ladder
  • Right stern deck
  • Shower Complete with surge tank, tank in prow, outdoor embarkation and installation
  • Complete dingy heuling belt kit for launch/accommodation
  • Anchor windlass installed with motor, cable, chain and double controls (in console and anchor housing)
  • Wake board kit complete with counterplates
  • Modification kit from Zar 65 to Zar 65 suite
  • Modification kit installation from Zar 65 to Zar 65 suite
  • Dashboard with ladder for double engine installation
  • Electric refrigerator (12/24V)
  • Modification of the ZAR 65 driver’s seat (for boats manufactured before September 2005)
  • Flexi-teak for cockpit
  • Flexi teak for the bridges + covers (4pz)
  • Flexi teak for the bridges (2pz)
  • Flexi-teak installation
  • Nautical camping tent
  • Sunroof 3 arch
  • Rear telescopic sun-cover for roll-bar
  • Prow sunroof (rear telescopic sun-cover extension)
  • Side canopy(1) for telescopic sun-cover

ZAR65

Posted on by
slide 1
slide 1
slide 1
slide 1
slide 1
Img
Img
Img
Img
Img
Img
previous arrow
next arrow

ZAR65

Features

  • 3 rows that can seat 8 persons forward running
  • anchor forepeaks and afterpeaks
  • back peak with the mooring accessories
  • front sun bathing bed convertible into a double bed (cm 150 x 195) with extension as an optional
  • wide stem dinette with a table as an optional
  • wide back peak;wide front peak
  • wide back dinette with a table included (only Suite version)
  • two side peaks in the stem sides
  • 160 x 190 back sunbathing bed (with the back rest in the horizontal position)
  • two-seater console with a hydraulic wheelhouse, stainless steel rudder, 1 internal compartment with door, an object holder and four peaks under the driver’s couch and under the front seat. Reclining driver’s couch
  • bilge pump
  • repairs kit
  • inflating device
  • a pair of paddles
  • 8 stainless steel handles for passengers safety
  • foldaway stainless steel ascent ramp and double VTR bridge
  • 1 reticular polypropylene fuel tank (about 240 litres) according to standards CE
  • 6 handling handles
  • 4 stainless steel bollards
  • perimetric double millpond
  • polished stainless steel 9 Kg anchor
  • anchor-winch nose with stainless steel bow
  • 3 stainless steel eyebolts for hangers

Technical Data

  • Static self emptyingHomologation "CE cat. "B"
  • Length m 6,50
  • Width m 2,55
  • Internal walking length m 6,40
  • Internal walking width m 2,00
  • Intertubular width m 1,50
  • Tubular diameter cm 53
  • Watertight compartments n. 6
  • Seating capacity n. 12
  • Net dinghy weight (without equipment, liquids or motor) ± 10% variable datum kg 880
  • Maximum power applicable kW 166/HP 225
  • Minimum power applicable (minimum performance) HP 85/CV115
  • Power recommended (average performance) HP 140/180
  • Engine shaft length L
  • on demand XL
  • Max. weight installable motors kg 400
  • CE certification with “B” design category and CE type testing. (A+a form).

Optional Equipment

  • Stainless steel roll-bar
  • Roll-bar installation with running lights, anchorage lights, horn and wiring
  • Beacon ready installed on roll-bar/console
  • Sunbed extension
  • Prow complete table
  • Auxiliary engine support
  • Total night cover
  • Partial night cover
  • Console cover
  • Seat cover
  • Electric panel
  • Left stern deck with folding ladder
  • Right stern deck
  • Shower Complete with surge tank, tank in prow, outdoor embarkation and installation
  • Complete dingy heuling belt kit for launch/accommodation
  • Anchor windlass installed with motor, cable, chain and double controls (in console and anchor housing)
  • Wake board kit completewith counterplates
  • Modification kit from Zar 65 to Zar 65 suite
  • Modification kit installation from Zar 65 to Zar 65 suite
  • Dashboard with ladder for double engine installation
  • Electric refrigerator (12/24V)
  • Modification of the ZAR 65 driver’s seat (for boats manufactured before September 2005)
  • Flexi-teak for cockpit
  • Flexi teak for the bridges + covers (4pz)
  • Flexi teak for the bridges (2pz)
  • Flexi-teak installation
  • Nautical camping tent
  • Sunroof 3 arch
  • Rear telescopic sun-cover for roll-bar
  • Prow sunroof (rear telescopic sun-cover extension)
  • Side canopy(1) for telescopic sun-cover

ZAR61 Suite Plus

Posted on by
slide 1
slide 1
slide 1
slide 1
slide 1
slide 1
Img
Img
Img
Img
Img
Img
Img
previous arrow
next arrow

ZAR61 Suite Plus

Features

  • 2 rows that can seat 6 persons forward running;
  • anchor forepeaks and afterpeaks;
  • back peak with the mooring accessories;
  • front sun bathing bed convertible into a double bed (cm 150 x 195) with extension as an optional;
  • wide stem dinette with a table as an optional;
  • wide back peak;
  • two side peaks in the stem sides;
  • 160 x 195 back sunbathing bed (with the back rest in the horizontal position);
  • wide back peak;
  • wide front peak;
  • two-seater console with a hydraulic wheelhouse, stainless steel rudder, 1 internal compartment door, an object holder and two peaks under the driver’s couch and under the front seat. Reclining driver’s couch with pantograph movement;
  • foldaway stainless steel ascent ramp and double VTR bridge;
  • bilge pump;
  • repairs kit;
  • inflating device;
  • a pair of paddles;
  • 7 stainless steel handles for passengers safety;
  • driver’s couch with double position (sitting up and down);
  • 1 reticular polypropylene fuel tank (about 200 litres) according to standards CE;
  • 4 handling handles;
  • 4 stainless steel bollards;
  • perimetric double millpond;
  • polished stainless steel 6,5 Kg anchor;
  • anchor-winch nose with stainless steel bow;
  • 3 stainless steel eyebolts for hangers.

Technical Data

  • Static self emptying
  • Homologation “CE cat. “B”
  • Length m 6.07
  • Width m 2.54
  • Internal walking length m 6.00
  • Internal walking width m 1.99
  • Intertubular width m 1.49
  • Tubular diameter cm 53
  • N. tubular compartments n. 6
  • Seating capacity n. 12
  • Net dinghy weight (with standard equipment, without liquids and motor) ± 10% variable datum kg 750
  • Maximum power applicable kW 133/HP 180
  • Minimum power applicable kW 85
  • (minimum performance) HP 115
  • Power recommended kW 96/133
  • (average performance) HP 130/180
  • Engine shaft length L
  • Max. weight installable motors kg 400
  • CE certification with “B” design category and CE type testing. (A+a form).

Optional Equipment

  • Stainless steel roll-bar
  • Roll-bar installation with running lights, anchorage lights, horn and wiring
  • Beacon ready installed on roll-bar/console
  • Sunbed extension
  • Prow complete table
  • Auxiliary engine support
  • Total night cover
  • Partial night cover
  • Console cover
  • Seat cover
  • Left stern deck with folding ladder
  • Right stern deck
  • Shower Complete with surge tank, tank in prow, outdoor embarkation and installation
  • Complete dingy heuling belt kit for launch/accommodation
  • Anchor windlass installed with motor, cable, chain and double controls (in console and anchor housing)
  • Eletric panel
  • Wake board kit complete with counterplates
  • Eletric refrigerator (12/24V)
  • Flexi-teak for cockpit
  • Felxi teak for the bridges + covers (4pz)
  • Felxi teak for the bridges (2pz)
  • Flexi-teak installation
  • Nautical camping tent
  • Sunroof 3 arch
  • Rear telescopic sun-cover for roll-bar
  • Prow sunroof (rear telescopic sun-cover extension)
  • Side canopy(1) for telescopic sun-cove

ZAR61 Suite

Posted on by
slide 1
slide 1
slide 1
slide 1
Img
Img
Img
Img
Img
previous arrow
next arrow

ZAR61 Suite

Features

  • 2 rows that can seat 6 persons forward running;
  • anchor forepeaks and afterpeaks;
  • back peak with the mooring accessories;
  • front sun bathing bed convertible into a double bed (cm 150 x 195) with extension as an optional;
  • wide stem dinette with a table as an optional;
  • wide back peak;
  • two side peaks in the stem sides;
  • 160 x 195 back sunbathing bed (with the back rest in the horizontal position);
  • wide back peak;
  • wide front peak;
  • two-seater console with a hydraulic wheelhouse, stainless steel rudder, 1 internal compartment door, an object holder and two peaks under the driver’s couch and under the front seat. Reclining driver’s couch with pantograph movement;
  • foldaway stainless steel ascent ramp and double VTR bridge;
  • bilge pump;
  • repairs kit;
  • inflating device;
  • a pair of paddles;
  • 7 stainless steel handles for passengers safety;
  • driver’s couch with double position (sitting up and down);
  • 1 reticular polypropylene fuel tank (about 200 litres) according to standards CE;
  • 4 handling handles;
  • 4 stainless steel bollards;
  • perimetric double millpond;
  • polished stainless steel 6,5 Kg anchor;
  • anchor-winch nose with stainless steel bow;
  • 3 stainless steel eyebolts for hangers.

Technical Data

  • Static self emptying
  • Homologation “CE cat. “B”
  • Length m 6.07
  • Width m 2.54
  • Internal walking length m 6.00
  • Internal walking width m 1.99
  • Intertubular width m 1.49
  • Tubular diameter cm 53
  • N. tubular compartments n. 6
  • Seating capacity n. 12
  • Net dinghy weight (with standard equipment, without liquids and motor) ± 10% variable datum kg 750
  • Maximum power applicable kW 133/HP 180
  • Minimum power applicable kW 85
  • (minimum performance) HP 115
  • Power recommended kW 96/133
  • (average performance) HP 130/180
  • Engine shaft length L
  • Max. weight installable motors kg 400
  • CE certification with “B” design category and CE type testing. (A+a form).

Optional Equipment

  • Stainless steel roll-bar
  • Roll-bar installation with running lights, anchorage lights, horn and wiring
  • Beacon ready installed on roll-bar/console
  • Sunbed extension
  • Prow complete table
  • Auxiliary engine support
  • Total night cover
  • Partial night cover
  • Console cover
  • Seat cover
  • Left stern deck with folding ladder
  • Right stern deck
  • Shower Complete with surge tank, tank in prow, outdoor embarkation and installation
  • Complete dingy heuling belt kit for launch/accommodation
  • Anchor windlass installed with motor, cable, chain and double controls (in console and anchor housing)
  • Eletric panel
  • Wake board kit complete with counterplates
  • Eletric refrigerator (12/24V)
  • Flexi-teak for cockpit
  • Felxi teak for the bridges + covers (4pz)
  • Felxi teak for the bridges (2pz)
  • Flexi-teak installation
  • Nautical camping tent
  • Sunroof 3 arch
  • Rear telescopic sun-cover for roll-bar
  • Prow sunroof (rear telescopic sun-cover extension)
  • Side canopy(1) for telescopic sun-cover

ZAR61

Posted on by
slide 1
Img
Img
previous arrow
next arrow

ZAR61

Features

  • 3 rows that can seat 8 persons forward running;
  • anchor forepeaks and afterpeaks;
  • back peak with the mooring accessories;
  • front sun bathing bed convertible into a double bed (cm 150 x 195) with extension as an optional;
  • wide stem dinette with a table as an optional;
  • wide back peak;
  • two side peaks in the stem sides;
  • 160 x 195 back sunbathing bed (with the back rest in the horizontal position);
  • wide back peak;
  • wide front peak;
  • two-seater console with a hydraulic wheelhouse, stainless steel rudder, 1 internal compartment door, an object holder and two peaks under the driver’s couch and under the front seat. Reclining driver’s couch with pantograph movement;
  • foldaway stainless steel ascent ramp and double VTR bridge;
  • bilge pump;
  • repairs kit;
  • inflating device;
  • a pair of paddles;
  • 7 stainless steel handles for passengers safety;
  • driver’s couch with double position (sitting up and down);
  • 1 reticular polypropylene fuel tank (about 200 litres) according to standards CE;
  • 4 handling handles;
  • 4 stainless steel bollards;
  • perimetric double millpond;
  • polished stainless steel 6,5 Kg anchor;
  • anchor-winch nose with stainless steel bow;
  • 3 stainless steel eyebolts for hangers

Technical Data

  • Static self emptying
  • Homologation “CE cat. “B”
  • Length m 6.07
  • Width m 2.54
  • Internal walking length m 6.00
  • Internal walking width m 1.99
  • Intertubular width m 1.49
  • Tubular diameter cm 53
  • N. tubular compartments n. 6
  • Seating capacity n. 12
  • Net dinghy weight (with standard equipment, without liquids and motor) ± 10% variable datum kg 750
  • Maximum power applicable kW 133/HP 180
  • Minimum power applicable kW 85
  • (minimum performance) HP 115
  • Power recommended kW 96/133
  • (average performance) HP 130/180
  • Engine shaft length L
  • Max. weight installable motors kg 400

Optional Equipment

  • Stainless steel roll-bar
  • Roll-bar installation with running lights, anchorage lights, horn and wiring
  • Beacon ready installed on roll-bar/console
  • Sunbed extension
  • Prow complete table
  • Auxiliary engine support
  • Total night cover
  • Partial night cover
  • Console cover
  • Seat cover
  • Left stern deck with folding ladder
  • Right stern deck
  • Shower Complete with surge tank, tank in prow, outdoor embarkation and installation
  • Complete dingy heuling belt kit for launch/accommodation
  • Anchor windlass installed with motor, cable, chain and double controls (in console and anchor housing)
  • Eletric panel
  • Wake board kit complete with counterplates
  • Eletric refrigerator (12/24V)

ZAR57 Welldeck

Posted on by
slide 1
Img
Img
previous arrow
next arrow

ZAR57 Welldeck

Features

  • 3 rows that can seat 8 persons forward running;
  • anchor forepeaks and afterpeaks;
  • back peak with the mooring accessories;
  • front sun bathing bed convertible into a double bed (cm 150 x 195) with extensions as an optional that includes dunnages and pillows, the middle dunnage with a stainless steel leg can be used as a table;
  • wide stem dinette with a table as an optional;
  • wide back peak;
  • wide front peak;
  • four side peaks in the stem sides;
  • 160 x 195 back sunbathing bed (with the back rest in the horizontal position);
  • two-seater console with a hydraulic wheelhouse,
  • stainless steel rudder, 2 internal compartments with door, an object holder and two peaks under the driver’s couch and under the front seat. Reclining driver’s couch with pantograph movement;
  • bilge pump;
  • repairs kit;
  • inflating device;
  • a pair of paddles;
  • 7 stainless steel handles for passengers safety

Technical Data

  • Static self emptying
  • Homologation “CE cat. “B”
  • Length m 5.77
  • Width m 2.54
  • Internal walking length m 5.70
  • Internal walking width m 2.00
  • Intertubular width m 1.44
  • Tubular diameter cm 53
  • N. tubular compartments n. 6
  • Seating capacity n. 12
  • Net dinghy weight kg 680
  • (with standard equipment, without liquids and motor) ± 10% variable datum
  • Maximum power kW 114/HP 155
  • Minimum power kW 52/ HP 70
  • Power recommended kW 67/111
  • (average performance) HP 90/150
  • Engine shaft length L
  • Max. weight installable motors kg 340

Optional Equipment

  • Stainless steel roll-bar
  • Roll-bar installation with running lights,anchorage lights, horn and wiring
  • Beacon ready installed on roll-bar/console
  • Prow sunbed extension with limber board and table legs
  • Auxiliary engine support
  • Total night cover
  • Partial night cover
  • Console cover
  • Seat cover
  • Left stern deck with folding ladder
  • Right stern deck
  • Shower Complete with surge tank, tank in prow,outdoor embarkation and installation
  • Complete dingy heuling belt kit for launch/accommodation
  • Anchor windlass installed with motor, cable, chain and double controls (in console and anchor housing)
  • Eletric panel
  • 7 kg stainless steel anchor
  • Wake board kit complete with counterplates
  • Electric refrigerator (12/24V)

ZAR53

Posted on by
slide 1
slide 1
slide 1
slide 1
slide 1
slide 1
slide 1
Img
Img
Img
Img
Img
Img
Img
Img
previous arrow
next arrow

ZAR53

Features

  • 3 rows that can seat 8 persons forward running;
  • front peak for the anchor with the side opening door;
  • back peak with the mooring accessories;
  • front sunbathing bed convertible into a double bed (cm 145 x 187) with extensions as an optional that includes dunnages and pillows, the middle dunnage with a stainless steel leg can be used as a table;
  • 145 x 130 back sunbathing bed (with back rest in the horizontal position) or 145 x 198 (with back rest + driver’s seat);
  • two-seater console with mechanical wheelhouse, stainless steel rudder, 2 internal watertight compartments with door, an object holder and two peaks under the driverís couch and under the front seat. Reclining driverís couch with pantograph movement;
  • foldaway stainless steel ascent ramp and VTR bridge;
  • 4 handling handles;
  • 4 stainless steel handles for passengers safety;
  •  stainless steel bollards;
  • perimetric double millpond;
  • anchor-winch nose;
  • 5 stainless steel (4 eyebolts for hangers);
  • repairs kit;
  • inflating device;
  • a pair of paddles;

Technical Data

  • Static self emptying
  • Homologation “CE cat. “C”
  • Length m 5.35
  • Width m 2.39
  • Internal walking length m 5.30
  • Internal walking width m 1.90
  • Intertubular width m 1.35
  • Tubular diameter cm 52
  • N. tubular compartments n. 6
  • Seating capacity n. 10
  • Net dinghy weight(with standard equipment, without liquids and motor) ± 10% variable datum kg 480
  • Maximum power kW 103/HP 140
  • Minimum power kW 52/HP 70
  • Power recommended kW 67/85
  • (average performance) HP 90/115
  • Engine shaft length L
  • Max. weight installable motors kg 320
  • CE certification with “B” design category and CE type testing. (A+a form).

Optional Equipment

  • Stainless steel tank of about 130 lt.
  • Tank installation in accordance with EC standards
  • Reticular polyethylene fuel tank of about 130 lt.
  • Reticular polyethylene fuel tank installation in accordance with EC standards
  • Fibreglass roll-bar
  • Overturning stainless steel roll-bar
  • Roll-bar installation with running lights, anchorage lights, horn and wiring
  • Beacon ready installed on roll-bar/console
  • Electric panel
  • Left stern deck with folding ladder
  • Right stern deck
  • Auxiliary engine support
  • Prow sunbed extension with limber board and table legs
  • “Stand up” cushion
  • Total night cover
  • Partial night cover
  • Console cover
  • Seat cover